
KUPER EFS.
For rapid and precise cutting of stacks of material.
Clean, tear-free and parallel cutting edges are the basis for a good joint. The KUPER EFS ensures the highest cutting quality due to its swinging knife motions cutting at an angle of 20 degrees. Cutting veneer transverse to the fiber direction can also be easily performed with the KUPER EFS.
The narrow design of the machine ensures the perfect view of the material and cutting surface every time. The cutting line is indicated by a guide light, guaranteeing an ultraprecise cut. Brake motor, gear drive and crank drive ensure rapid and powerful knife motion.
The width dimensions are approached automatically by the integrated positioning control. The pressure bar is lowered and as soon as the target pressure is reached, the cut is triggered. An angular set-up is recommended combined with the KUPER QFS cross cutting clipper. The support table with rip fence provides sufficient surface for comfortable handling even for very wide materials.
KUPERPOWER for your business.



Advantages at a glance.
- The Single Knife Veneer Guillotine KUPER EFS cuts of highest quality thanks to the swinging and powerful drawing motion of the knife at an angle of approx. 20°.
- Parallel fence with high-speed motordriven positioning, fine adjustment and digital gauge for cutting parallel face veneers and edge lippings.
- Clearly visible marking of the cutting line by means of a green guide light.
- Guide markings and an angular fence on the machine table for easier alignment of the material.
- Broad pressure bar for pressing even wavy veneer materials and level prior to cutting.
- Precut facility with hydraulic adjustment of the cutter bar by 0.9 mm. Precutting and finish-cutting of the pressed material produces right-angled cut faces.
- Powerful crank drive enables the cutting of veneer across the grain.
- High pressing and cutting forces are reliably absorbed by the heavy-duty construction.
- Precise and permanent parallel guidance of machine components.
- Knife with 30 mm grinding allowance for longest possible use.
- Intermittent operation of the drives results in a low energy requirement and a low level of noise.
- Occupational safety regulations are met by a light barrier safety device, two-hand operation, electric safety control system and protective gratings at the rear.
Deep support table
The support table allows cutting dimensions of 20 - 720 mm width. The corresponding stable rip fence is managed by the machine control. The support table offers high precision and speed of movement. The result: dimensionally accurate, parallel cutting edges with maximum efficiency. Upon request the support table is also available in an ultra-low version.
Option precision cut:
With the help of the precision cutting device, thicker and more difficult veneers can be cut even more precisely. The precut as well as the subsequent precision cut avoid chipping on the undersides of the veneers.


The KUPER EFS cuts:
- Veneer
Upon request:
- PVC
- All-plastic
- Polystyrol
- Acryl
- Honeycomb boards
- Papers
- Plastic films
- Cardboard
- and much more

Visible marking of cutting line
Clearly visible marking of the cutting line by means of a guide light.

Cuts of highest quality
Straight and parallel cutting of the veneers – Maximum precision in cutting ensures the tight-joint splicing after the cut for all kinds of veneer.

Swinging and powerful drawing motion
Cuts of highest quality thanks to the swinging and powerfull drawing motion of the knife at an angle of approx. 20°.

Easy operation
Telescreen positioning control system fordiverse modes of operation and storableprogram operations.
Technical data.
Cutting length | 2,800 mm |
Insertion height | 80 mm |
Parallel fence range | 20-720 mm * |
Pressure bar | hydraulic cylinder, 2 pressure stages |
Cutter bar | brake motor, gearing, crank drive |
Parallel fence | three-phase a.c. motor, positioning drive |
Connected load | 7.7 kW ** |
Floor space (with parallel fence) | 496 x 182 cm |
Height | 170 cm |
Net weight | 3,900 kg |
*...upon request different range possible **electric controls on left if requested We reserve the right to make technical modifications without notice. |
Cutting length | 3,200 mm |
Insertion height | 80 mm |
Parallel fence range | 20-720 mm * |
Pressure bar | hydraulic cylinder, 2 pressure stages |
Cutter bar | brake motor, gearing, crank drive |
Parallel fence | three-phase a.c. motor, positioning drive |
Connected load | 7.7 kW ** |
Floor space (with parallel fence) | 537 x 182 cm |
Height | 170 cm |
Net weight | 4,300 kg |
*...upon request different range possible **electric controls on left if requested We reserve the right to make technical modifications without notice. |
Cutting length | 4,200 mm |
Insertion height | 80 mm |
Parallel fence range | 20-720 mm * |
Pressure bar | hydraulic cylinder, 2 pressure stages |
Cutter bar | brake motor, gearing, crank drive |
Parallel fence | three-phase a.c. motor, positioning drive |
Connected load | 7.7 kW ** |
Floor space (with parallel fence) | 636 x 182 cm |
Height | 170 cm |
Net weight | 5,400 kg |
*...upon request different range possible **electric controls on left if requested We reserve the right to make technical modifications without notice. |
Additional technical data upon request. Illustrations may contain options. Additional components such as control cabinets, safety facilities e.g. are maybe not shown. Subject to design modification.
Do you have any questions?

- Klaus Schlütermann
Sales Manager - +49 52 44/9 84 - 3 42
- klaus.schluetermann@KUPER.de